Parts source near me is a phrase you can use with all of your lathe needs. Parts with axial symmetry have a very important place in manufacturing. In this article, we will learn about the parts of the lathes used in the production of screws, shafts and many other cylindrical products, the items used and the selection criteria, and we will talk about the safety precautions to be followed when working with lathes. These are the actual turned parts meaning and pieces;
Lathe Chucks
This part is for central fastening of cylindrical parts (diameters up to 200-300 mm). Triangular and hexagonal parts are also attached to this chuck. When the chuck switch is turned, the feet move at the same time. When you need chunks, you can search Parts source near me online.
Four-legged universal chucks are used for four-point centering and clamping of square-section workpieces in addition to parts connected to three-legged chucks. In universal chucks, all feet move at the same time.
Vise
Chuck It is used to connect round square and irregular poured or hammered parts. Each foot moves independently of each other. This binding process can be done with the desired sensitivity. Workpieces that cannot be attached to pedestal chucks in terms of movement. Perforated Flat Chuck Shapes are attached to the perforated flat chucks with various bolts.
Swivel Chucks name is given because of the swivel attached to the workpiece in order to be able to turn between two centers. The workpiece is processed by attaching the swivel tail on the chuck. The swivel is fixed to the chuck with a pin. If you have this Chuck and youre having problems, you can search ‘repair parts near me’ online.
Combined Chuck
These chucks have the mechanical properties of universal and clamped chucks. The parts that we can connect in both chucks can be connected to this chuck. For this process, the screw allows the feet to move together and the foot movement screws to pieces one by one. This can be a tricky searh when you need one, you might do more than the parts source near me search.
· Magnetic Chuck
These chucks are used to attach workpieces to the face surface with their magnetization feature. Its feature is that it enables the attachment of small or thin parts that cannot be attached to other chucks (such as connecting circlips and rings).
· Collets:
The flexible sleeves that are used to connect small fully rounded and properly processed workpieces to the lathe are called collets. They are used for clamping rod-shaped cylindrical, square or hexagonal workpieces. They are commonly used in revolver and index (automatic) lathes. In addition, in CNC machining centers, pliers are used to connect cylindrical shank cutters. It is used with special collet head on different projects such as turned wood parts.
Work Patterns
Apparatuses and fastening mechanisms created according to the characteristics of the work in mass production are called work patterns. Connecting and processing identical parts separately will take time and will not be economical, for this reason work clamping molds are used. This is especially important in terms of reducing the cost by saving time in mass production. So you might need a custom one and it is important to say what do you need when you search for the ‘Parts source near me’.
· Cutting Fluid
Cutting fluids are used in order to reduce the heat caused by friction between the pencil and the workpiece, to increase the surface quality of the workpiece, and to provide high quality and comfortable cutting while the cutting process is carried out on lathes. In the selection of cutting fluid, the type of cutter and the type of operation should be taken into account, and the appropriate cutting fluid should be selected from the catalogues.
Effect on Cutting: The cutters heat up quickly due to friction during chip removal. This increase in heating may cause the breaker to break down. Due to the difficulty of the cutting process, the cutter wears out quickly and the life of the tool is reduced in chip removal with a defective pencil. This also increases the cost. When removing chips, heat will increase due to friction. Increasing the temperature will cause thermal expansions on the workpiece. With thermal expansion, there will be size differences in the workpiece and the surface quality will deteriorate. Cutting fluids are used to minimize these undesirable situations. You can find different cutting fluids from different turned parts manufacturer firms.
Recognizing Lathe Tools and Choosing the Tool for a Job
Choosing a suitable pen in every aspect according to the work to be done in the lathe is very important in terms of making the turning process flawless. Starting a job with an item that is not suitable for the construction of a job not only prevents the job from being processed correctly, but also prolongs the construction time of the job and increases the processing cost. So when choosing a pen for a job:
· Appropriate chuck selection should be made according to cutting speed, feed rate and revolution number. You can find the right Chuck for you by searching with the words ‘Parts source near me’ online.
· The pen should be selected according to the type of material to be processed. For example, a high-carbon material such as Ç1070 can be processed at low speed with a high-quality serial steel pen (HSS). If this process is to be done in large quantities, it may take a long time to be done with this item. If many parts are to be processed, the wear time of the pencil is shortened and the cost increases.
· Instead, it can be processed in a shorter time at higher speed with a hard metal tip blade with cnc turned parts.
· Materials that are difficult to machine and have high hardness can be processed at higher cutting speeds with hard metal inserts by selecting the appropriate turned parts.
Comments